Gasklephuis inleren gaat helaas niet bij deze motor en de digifrant 3.0 zie hier van gerrit speek
daarbij zijn alle label files die ik van de digifrant 3.0 heb zonder deze optie uitgerust of ik moet het niet zien
Het inleren van het Gasklephuis kan worden uitgevoerd EN bij 'Drive-By-Wire' (DBW of E-gas) auto's EN bij auto's met een klassieke (Bowden) mechanische kabel, als er tenminste GEEN Idle Stabilization Valve (ISV) aanwezig is. Als die ISV wel aanwezig is dan is er geen gemotoriseerde controle van de gasklep.
daarbij zijn alle label files die ik van de digifrant 3.0 heb zonder deze optie uitgerust of ik moet het niet zien
;***********************************************************************************
; ECU : DIGIFANT 3.0
; FIRMWARE :
; ECU PART NUMBER : 037 906 024 G/AB
; MODELS COVERED : VW Golf III (1H) / VW Passat / SEAT Toledo & Ibiza
; ENGINE CODE : ABF
; REVISION HISTORY : 22/06/15 Rev 1.0
;***********************************************************************************
;
000,0,Basic Functions
000,1,Intake air temperature,Specification: 73...24 (15...50 ?C)
000,2,Battery voltage,Specification: 128...150 (12.0...14.2 V)
000,3,Coolant temperature,Specification: 4...10 (85...105 ?C)
000,4,Engine load,Specification: 60...90 (23...36 %)
000,5,Lambda probe signal,Specification: 240...100 (0...1.0 V)
000,6,Lambda control time counter,Specification: 0
000,7,Lambda probe status counter,Specification: 0...20
000,8,Throttle valve potentiometer voltage,Specification: 12...49 (0.25...0.95 V)
000,9,Injection period,Specification: 5...8 (2.5...4.0 ms)
000,10,Engine speed,Specification: 212...202 (770...890 rpm)
;
;Display Zone 7: When the Lambda probe does not supply a signal the counter counts high (e.g. probe cold).
; The value can rise to 127 when, for example, the probe heating or the probe wiring is defective.
; Check in "Read measured value block" function!
;
;Display Zone 4: The specifications are valid for an altitude up to max. 300m above sea level.
;
;Display Zone 3: Before initiating the basic setting the coolant temp value must be 4...10 (corresponds to 85...105 ?C).
;
001,0,Basic Functions
001,1,Coolant temperature,,Specification: 79...116 ?C
001,2,Engine speed,,Specification: 780...900 rpm
001,3,Lambda probe voltage,,Specification: 0...1.0 V
001,4,Injection period,,Specification: 2.5...4.0 ms
;
; Injection period spec at idling, coolant temperature min. 80 ?C
;
002,0,Idle Stabilization
002,1,Coolant temperature,,Specification: 79...116 ?C
002,2,Engine speed,,Specification: 780...900 rpm
002,3,Throttle valve angle,,Specification: 0...86 <?
002,4,Engine load,,Specification: 23...36 %
;
; Engine load specifications are valid for an altitude up to max. 300 m above sea level.
;
003,0,Group Functions
003,1,Coolant temperature,,Specification: 79...116 ?C
003,2,Engine speed,,Specification: 780...900 rpm
003,3,Intake air temperature,,Specification: 12...70 ?C
003,4,Battery voltage,,Specification: 10.8...15.0 V
;
004,0,Operating Condition
004,1,Coolant temperature,,Specification: 79...116 ?C
004,2,Engine speed,,Specification: 780...890 rpm
004,3,Ignition timing (calculated),, <?
004,4,Engine load,,Specification: 23...36 %
;
; Engine load specifications are valid for an altitude up to max. 300 m above sea level.
;
005,0,Group Functions
005,1,Coolant temperature,,Specification: 79...116 ?C
005,2,Engine speed,,Specification: 780...900 rpm
005,3,Throttle valve angle,,Specification: 0...86 <?
005,4,Battery voltage,,Specification: 10.8...15.0 V